Linux 纯终端字体配置

今天决定尝试更改纯终端字体,由于Linux加载时有一行消息是说set font and keymap之类,于是我从/etc/init.d下手.

首先grep "font" *, 发现有关脚本是console-screen.sh 和 console-setup.

一开始研究的是console-screen.sh,里面调用的命令是consolechars, 但是试了几次都不管用, 后来看到这个脚本开始几行会判断setupcon是否存在,如果是就直接退出了.

然后就看console-setup, 里面也是调用的setupcon

于是目标锁定setupcon, 看了看help, 得知配置文件在/etc/default/console-setup, 而字体文件在/usr/share/consolefonts, 里面有一大堆psf文件

这样,先找好字体(当然自己弄也可以),然后在console-setup里,修改对应的CODESET, FONTFACE, FONTSIZE, 最后sudo /etc/init.d/console-setup restart 就行了.

现在正在研究如何把ttf转成psf, 好像不大容易的样子.

Comments

Determine Perspective Lines With Off-page Vanishing Point

In perspective drawing, a vanishing point represents a group of parallel lines, in other words, a direction. For any point on the paper, if we want a line towards the same direction (in the 3d space), we simply draw a line through it and the vanishing point. But sometimes the vanishing point is too far away, such that it is outside the paper/canvas. In this example, we have a point P and two perspective lines L1 and L2. The vanishing point VP is naturally the intersection of L1 and L2. The task is to draw a line through P and VP, without having VP on the paper. I am aware of a few traditional solutions: 1. Use extra pieces of paper such that we can extend L1 and L2 until we see VP. 2. Draw everything in a smaller scale, such that we can see both P and VP on the paper. Draw the line and scale everything back. 3. Draw a perspective grid using the Brewer Method. #1 and #2 might be quite practical. #3 may not guarantee a solution, unless we can measure distances/p...

Installing Linux on Surface Pro 1g

Windows 10 will soon reach its end of life, and my 1-gen Surface Pro is not supported by Windows 11. I (finally) decided to install Linux to it. Fortunately, it's a not-so-easy nice adventure: The device has only one USB port, so I have to bring back my 10+-year old USB hub. My live USB drive cannot boot directly, I have to disable Secure Boot first, by holding Volume Up during boot. I think years ago I learned that booting on USB might not work through a USB hub, but fortunatelly it worked well with my setup. This is done by holding Volume Down during boot. Wifi adapter was detected in the live Linux environment, but not functional. And I don't have a USB-Ethernet adapter. Luckily, nowadays we have USB-tethering from Android phones, which works out-of-the-box. Originally I planned to following this guide to set up root on ZFS, however, the system froze when building the ZFS kernel module. Then I decided to just use EXT4, yet I still learned a lot from the guide about disk par...

Fix Google Security Code

Google Security Code (http://g.co/sc) is one type of 2-step verification. This is particularly useful when security keys and passkeys are not available. I have been using it in my LXC containers, until today I found out that it stopped working. It just kept saying "The code is invalid". It is easy to rule out some factors: The code works on other browsers on my laptop. The code works on other devices that are directly connected to the router. So it appears that Google also checks IP addresses besides the security code. Recently I have IPv6 enabled, so most devices that are directly connected to the router have both IPv4 and IPv6 addresses. But I only enabled IPv4 for my LXC containers. So I guess when a code is generated by device A and used by device B, Google should be able to check that device A and device B are closely located. But in my case, IPv6 address appears on device A but not on device B, which may look suspicious. To fix the problem, I just needed to disable IPv...

WangLu's Notes

Search This Blog