中文 console jfbterm

今天搞明白了jfbterm的用法

/etc/jfbterm.conf里有各种编码和字体文件的对应关系

然后jfbterm --reset=<编码> 运行,或者运行后切换编码

简体中文用GB2312
utf8用UTF8

另外好像应该修改LC_ALL(准确的说是LC_CTYPE).

BIG5默认没有打开,好像是靠iconv转码后输出

现在感觉utf-8的字体英文较好,GB2312的中文不错.
它不与w3m-img冲突!!因此可以同时看中文和图片!!太棒了!!

一个问题是退出时常常死机,但是按Ctrl-Alt-Del可以重启
另一个问题是没有输入法,有待解决

Comments

Determine Perspective Lines With Off-page Vanishing Point

In perspective drawing, a vanishing point represents a group of parallel lines, in other words, a direction. For any point on the paper, if we want a line towards the same direction (in the 3d space), we simply draw a line through it and the vanishing point. But sometimes the vanishing point is too far away, such that it is outside the paper/canvas. In this example, we have a point P and two perspective lines L1 and L2. The vanishing point VP is naturally the intersection of L1 and L2. The task is to draw a line through P and VP, without having VP on the paper. I am aware of a few traditional solutions: 1. Use extra pieces of paper such that we can extend L1 and L2 until we see VP. 2. Draw everything in a smaller scale, such that we can see both P and VP on the paper. Draw the line and scale everything back. 3. Draw a perspective grid using the Brewer Method. #1 and #2 might be quite practical. #3 may not guarantee a solution, unless we can measure distances/p...

Chasing an IO Phantom

My home server has been weird since months ago, it just becomes unresponsive occassionally. It is annoying but it happens only rarely, so normally I'd just wait or reboot it. But weeks ago I decided to get to the bottom of it. What's Wrong My system set up is: Root: SSD, LUKS + LVM + Ext4 Data: HDD, LUKS + ZFS 16GB RAM + 1GB swap Rootless dockerd The system may become unresponsive, when the IO on HDD is persistantly high for a while. Also: Often kswapd0 has high CPU High IO on root fs (SSD) From dockerd and some containers RAM usage is high, swap usage is low It is very strange that IO on HDD can affect SSD. Note that when this happens, even stopping the IO on HDD does not always help. Usually restarting dockerd does not help, but rebooting helps. Investigation: Swap An obvious potential root cause is the swap. High CPU on kswapd0 usually means the free memory is low and the kernel is busy exchanging data between disk and swap. However, I tried the following steps, none of the...

Fix Google Security Code

Google Security Code (http://g.co/sc) is one type of 2-step verification. This is particularly useful when security keys and passkeys are not available. I have been using it in my LXC containers, until today I found out that it stopped working. It just kept saying "The code is invalid". It is easy to rule out some factors: The code works on other browsers on my laptop. The code works on other devices that are directly connected to the router. So it appears that Google also checks IP addresses besides the security code. Recently I have IPv6 enabled, so most devices that are directly connected to the router have both IPv4 and IPv6 addresses. But I only enabled IPv4 for my LXC containers. So I guess when a code is generated by device A and used by device B, Google should be able to check that device A and device B are closely located. But in my case, IPv6 address appears on device A but not on device B, which may look suspicious. To fix the problem, I just needed to disable IPv...

WangLu's Notes

Search This Blog