Skip to main content

Ascii Art: figlet

有个程序叫做figlet, 跟banner类似,不过支持的字体和字符集都很丰富。

学校源里就有,装有有那么20来个字体,我都看了一遍,挺不错。

然后发现它似乎支持utf和cjk之类的,但是试了试没有成功。于是又用aptitude看这个包,有两个suggest,figfonts和figfonts-cjk,是字体包,而源里都没有,我去debian下了个figfonts,然后字体猛地多了好多好多,我不得不写个程序看看这些都如何。里面确实有很多好看&好玩的,如caligraphy, poison, smblood等都挺有特色。

但是figfonts-cjk似乎不是那么好下,debian上的就不行。我再找找看。

Comments

Popular posts from this blog

Determine Perspective Lines With Off-page Vanishing Point

In perspective drawing, a vanishing point represents a group of parallel lines, in other words, a direction. For any point on the paper, if we want a line towards the same direction (in the 3d space), we simply draw a line through it and the vanishing point. But sometimes the vanishing point is too far away, such that it is outside the paper/canvas. In this example, we have a point P and two perspective lines L1 and L2. The vanishing point VP is naturally the intersection of L1 and L2. The task is to draw a line through P and VP, without having VP on the paper. I am aware of a few traditional solutions: 1. Use extra pieces of paper such that we can extend L1 and L2 until we see VP. 2. Draw everything in a smaller scale, such that we can see both P and VP on the paper. Draw the line and scale everything back. 3. Draw a perspective grid using the Brewer Method. #1 and #2 might be quite practical. #3 may not guarantee a solution, unless we can measure distances/p...

Installing Linux on Surface Pro 1g

Windows 10 will soon reach its end of life, and my 1-gen Surface Pro is not supported by Windows 11. I (finally) decided to install Linux to it. Fortunately, it's a not-so-easy nice adventure: The device has only one USB port, so I have to bring back my 10+-year old USB hub. My live USB drive cannot boot directly, I have to disable Secure Boot first, by holding Volume Up during boot. I think years ago I learned that booting on USB might not work through a USB hub, but fortunatelly it worked well with my setup. This is done by holding Volume Down during boot. Wifi adapter was detected in the live Linux environment, but not functional. And I don't have a USB-Ethernet adapter. Luckily, nowadays we have USB-tethering from Android phones, which works out-of-the-box. Originally I planned to following this guide to set up root on ZFS, however, the system froze when building the ZFS kernel module. Then I decided to just use EXT4, yet I still learned a lot from the guide about disk par...

Fix Google Security Code

Google Security Code (http://g.co/sc) is one type of 2-step verification. This is particularly useful when security keys and passkeys are not available. I have been using it in my LXC containers, until today I found out that it stopped working. It just kept saying "The code is invalid". It is easy to rule out some factors: The code works on other browsers on my laptop. The code works on other devices that are directly connected to the router. So it appears that Google also checks IP addresses besides the security code. Recently I have IPv6 enabled, so most devices that are directly connected to the router have both IPv4 and IPv6 addresses. But  I only enabled IPv4 for my LXC containers. So I guess when a code is generated by device A and used by device B, Google should be able to check that device A and device B are closely located. But in my case, IPv6 address appears on device A but not on device B, which may look suspicious. To fix the problem, I just needed to disable IPv...