Skip to main content

gnome panel 妙用一则 | A nice trick of gnome panel



链接: http://www.webupd8.org/2010/12/use-gnome-panel-as-wingpanel-quick-tip.html

结果如图,当panel上东西比较少的时候很实用。
操作步骤是在panel属性里取消expand,然后选中autohide,然后拖到右上角,通过gconf修改/apps/panel/toplevels/<panel name>/hide_delay为2147483647




Link: http://www.webupd8.org/2010/12/use-gnome-panel-as-wingpanel-quick-tip.html

Result as the picture above, quite useful when not too much things on the panel.
To make it like this, in the "properties“ dialog of the panel, cancel "expand" and select "autohide". Then drag the panel to the top-right of the screen. At last change the gconf value "/apps/panel/toplevels/<panel name>/hide_delay" to 2147483647

Comments

Popular posts from this blog

Determine Perspective Lines With Off-page Vanishing Point

In perspective drawing, a vanishing point represents a group of parallel lines, in other words, a direction. For any point on the paper, if we want a line towards the same direction (in the 3d space), we simply draw a line through it and the vanishing point. But sometimes the vanishing point is too far away, such that it is outside the paper/canvas. In this example, we have a point P and two perspective lines L1 and L2. The vanishing point VP is naturally the intersection of L1 and L2. The task is to draw a line through P and VP, without having VP on the paper. I am aware of a few traditional solutions: 1. Use extra pieces of paper such that we can extend L1 and L2 until we see VP. 2. Draw everything in a smaller scale, such that we can see both P and VP on the paper. Draw the line and scale everything back. 3. Draw a perspective grid using the Brewer Method. #1 and #2 might be quite practical. #3 may not guarantee a solution, unless we can measure distances/p...

Installing Linux on Surface Pro 1g

Windows 10 will soon reach its end of life, and my 1-gen Surface Pro is not supported by Windows 11. I (finally) decided to install Linux to it. Fortunately, it's a not-so-easy nice adventure: The device has only one USB port, so I have to bring back my 10+-year old USB hub. My live USB drive cannot boot directly, I have to disable Secure Boot first, by holding Volume Up during boot. I think years ago I learned that booting on USB might not work through a USB hub, but fortunatelly it worked well with my setup. This is done by holding Volume Down during boot. Wifi adapter was detected in the live Linux environment, but not functional. And I don't have a USB-Ethernet adapter. Luckily, nowadays we have USB-tethering from Android phones, which works out-of-the-box. Originally I planned to following this guide to set up root on ZFS, however, the system froze when building the ZFS kernel module. Then I decided to just use EXT4, yet I still learned a lot from the guide about disk par...

Fix Google Security Code

Google Security Code (http://g.co/sc) is one type of 2-step verification. This is particularly useful when security keys and passkeys are not available. I have been using it in my LXC containers, until today I found out that it stopped working. It just kept saying "The code is invalid". It is easy to rule out some factors: The code works on other browsers on my laptop. The code works on other devices that are directly connected to the router. So it appears that Google also checks IP addresses besides the security code. Recently I have IPv6 enabled, so most devices that are directly connected to the router have both IPv4 and IPv6 addresses. But  I only enabled IPv4 for my LXC containers. So I guess when a code is generated by device A and used by device B, Google should be able to check that device A and device B are closely located. But in my case, IPv6 address appears on device A but not on device B, which may look suspicious. To fix the problem, I just needed to disable IPv...