让LaTeX支持utf8

买了直通车，可以下到cyberbit.ttf了，于是想试试utf-8的LaTeX

步骤是：

1.到http://www.unruh.de/DniQ/latex/unicode/下载安装unicode.tgz
这一步我没有做，我是用apt装的latex-ucs

2.到ftp://ftp.netscape.com/pub/communicator/extras/fonts/windows/ 下个cyberbit.ttf
copy至/usr/share/texmf/fonts/truetype/CJK

3.下载http://edt1023.sayya.org/tex/ipeucs/cyberb.sh，放在临时目录下，并把cyberbit.ttf也拷过来，运行cyberb.sh

4.依下表将生成的文件/目录拷到对应位置
tfm /usr/share/texmf/fonts/tfm/CJK/cyberb
enc /usr/share/texmf/pdftex/enc
cyberb.map /usr/share/texmf/pdftex/config/cyberb.map

注意，第一行表示把生成的tfm目录中的所有文件拷到/usr/.../cyberb/中去，第二行类似

5.在/usr/share/texmf/pdftex/config/cyberb.map末尾加上一句
map +cyberb.map

6.好像需要在/usr/share/texmf下运行texhash,不知道是否是必需的。

这样就弄完了

本来ucs的doc中说使用方法是
\usepackage{ucs}
\usepackage[utf8]{inputenc}
然后文档中直接打中文就行了
但是我这不行

我发现CJK的utf8可以用了，方法是
\usepackage{CJK}

...

\begin{CJK}{UTF8}{song}
中文
\end{CJK}

当然了，tex文档要以utf8编码保存

字体还行吧，我对字体美观程度要求还不算高。
以后再研究研究怎么弄ucs

Comments

Determine Perspective Lines With Off-page Vanishing Point

In perspective drawing, a vanishing point represents a group of parallel lines, in other words, a direction. For any point on the paper, if we want a line towards the same direction (in the 3d space), we simply draw a line through it and the vanishing point. But sometimes the vanishing point is too far away, such that it is outside the paper/canvas. In this example, we have a point P and two perspective lines L1 and L2. The vanishing point VP is naturally the intersection of L1 and L2. The task is to draw a line through P and VP, without having VP on the paper. I am aware of a few traditional solutions: 1. Use extra pieces of paper such that we can extend L1 and L2 until we see VP. 2. Draw everything in a smaller scale, such that we can see both P and VP on the paper. Draw the line and scale everything back. 3. Draw a perspective grid using the Brewer Method. #1 and #2 might be quite practical. #3 may not guarantee a solution, unless we can measure distances/p...

Chasing an IO Phantom

My home server has been weird since months ago, it just becomes unresponsive occassionally. It is annoying but it happens only rarely, so normally I'd just wait or reboot it. But weeks ago I decided to get to the bottom of it. What's Wrong My system set up is: Root: SSD, LUKS + LVM + Ext4 Data: HDD, LUKS + ZFS 16GB RAM + 1GB swap Rootless dockerd The system may become unresponsive, when the IO on HDD is persistantly high for a while. Also: Often kswapd0 has high CPU High IO on root fs (SSD) From dockerd and some containers RAM usage is high, swap usage is low It is very strange that IO on HDD can affect SSD. Note that when this happens, even stopping the IO on HDD does not always help. Usually restarting dockerd does not help, but rebooting helps. Investigation: Swap An obvious potential root cause is the swap. High CPU on kswapd0 usually means the free memory is low and the kernel is busy exchanging data between disk and swap. However, I tried the following steps, none of the...

Fix Google Security Code

Google Security Code (http://g.co/sc) is one type of 2-step verification. This is particularly useful when security keys and passkeys are not available. I have been using it in my LXC containers, until today I found out that it stopped working. It just kept saying "The code is invalid". It is easy to rule out some factors: The code works on other browsers on my laptop. The code works on other devices that are directly connected to the router. So it appears that Google also checks IP addresses besides the security code. Recently I have IPv6 enabled, so most devices that are directly connected to the router have both IPv4 and IPv6 addresses. But I only enabled IPv4 for my LXC containers. So I guess when a code is generated by device A and used by device B, Google should be able to check that device A and device B are closely located. But in my case, IPv6 address appears on device A but not on device B, which may look suspicious. To fix the problem, I just needed to disable IPv...

WangLu's Notes

Search This Blog